início

Cartuchos e sensores

G6G7G8EXOCartridges and SensorsLocation BeaconBlackline LiveBlackline AnalyticsLoner MobileNotificationsGlossary
G6G7G8EXOCartridges and SensorsLocation BeaconBlackline LiveBlackline AnalyticsLoner MobileNotificationsGlossary

Central de Ajuda

Pesquisar na Central de Ajuda

Mostrar índice

Mostrar seções da página

miniaturaCartuchos e sensores

Pedido de teste de resposta e calibração de sensores de gás

Pedido de teste de resposta e calibração de sensores de gás

Atualizado em 1º de novembro de 2024.

This article describes the order in which you should bump test or calibrate your G7, G8, and EXO gas sensors. This article can be referenced when manually bump testing or calibrating your G7, G8, or EXO, and when bump testing or calibrating your G7 or G8 using G7/G8 Dock.

Não utilize cilindros de gás vencidos para testes de funcionamento e calibração. O gás vencido pode afetar a precisão dos testes de funcionamento e da calibração.

Determinação dos testes de resposta e da calibração de sensores de gás Pedido

When bump testing and calibrating G7, G8, and EXO, to avoid sensor cross-sensitivity, you must consider the order in which you test your gas sensors. The gas order you select depends on the gas sensors your device is equipped with, and whether you are using single gas or combination gas cylinders.

Blackline Safety recommends that you use the following flow charts to determine the order in which you are going to bump test or calibrate your gas sensors.

The recommended order is the same whether you manually bump test and calibrate your G7 or G8 device or use G7/G8 Dock.

Observação:

G7/G8 Dock will bump test and calibrate your device in the same order as the gas inlets, starting at inlet 1 and finishing at inlet 4. If your G7/G8 Dock is configured such that your bump test or calibration sequence is different than the flow charts below, your G7/G8 Dock gas inlets should be reconfigured to match the sequence outlined in the gas order flow charts.


Teste de funcionamento ou calibração utilizando o pedido de gás Fluxogramas

  1. Identifique os gases que você precisa submeter ao teste de funcionamento ou calibrar.
  2. Verifique qual fluxograma de pedidos de gás (cilindro de gás único ou cilindro de gás combinado) você deve consultar.
  3. Determine a ordem em que você precisa testar seus gases, comparando os sensores de gás que você está testando com a ordem descrita no fluxograma de testes de gás apropriado.
    Observação:

    G7/G8 Dock will bump test and calibrate your device in the same order as the gas inlets, starting at inlet 1 and finishing at inlet 4.

  4. Faça o teste de resposta ou a calibração de cada gás na ordem indicada no fluxograma.
    Importante:

    Always bump test or calibrate your device using calibration gas concentrations appropriate for your G7 or G8 device configuration. For more information on configuring calibration gas concentrations, refer to the Blackline Live support pages.

Always follow the prompts on your G7 or G8 to ensure that the procedure test times and flow rates are appropriate to the gas you are testing.

Always follow Blackline’s recommendations for configuring your G7/G8 Dock gas inlets. For example, in the case where Cl2 and NH3 sensors are on the same cartridge, connect the Cl2 gas cylinder to inlet 1, and connect NH3 to inlet 2. For more information, refer to the G7 Dock Technical User Manual.

EXO
G7
Cartucho multigás
Cartucho de gás único
Cartuchos

Last updated: October 13, 2026