home

Cartucce e sensori

G6G7G8EXOCartridges and SensorsLocation BeaconBlackline LiveBlackline AnalyticsLoner MobileNotificationsGlossary
G6G7G8EXOCartridges and SensorsLocation BeaconBlackline LiveBlackline AnalyticsLoner MobileNotificationsGlossary

Centro assistenza

Cerca nel Centro assistenza

Mostra sommario

Mostra sezioni della pagina

miniaturaCartucce e sensori

Ordine per il test di funzionamento e la taratura dei sensori di gas

Ordine per il test di funzionamento e la taratura dei sensori di gas

Aggiornato il 1° novembre 2024.

This article describes the order in which you should bump test or calibrate your G7, G8, and EXO gas sensors. This article can be referenced when manually bump testing or calibrating your G7, G8, or EXO, and when bump testing or calibrating your G7 or G8 using G7/G8 Dock.

Non utilizzare bombole di gas scadute per il test di funzionamento e la taratura. Il gas scaduto potrebbe compromettere l'accuratezza del test di funzionamento e della taratura.

Determinazione dei test di verifica e della calibrazione dei sensori di gas Ordine

When bump testing and calibrating G7, G8, and EXO, to avoid sensor cross-sensitivity, you must consider the order in which you test your gas sensors. The gas order you select depends on the gas sensors your device is equipped with, and whether you are using single gas or combination gas cylinders.

Blackline Safety recommends that you use the following flow charts to determine the order in which you are going to bump test or calibrate your gas sensors.

The recommended order is the same whether you manually bump test and calibrate your G7 or G8 device or use G7/G8 Dock.

Nota:

G7/G8 Dock will bump test and calibrate your device in the same order as the gas inlets, starting at inlet 1 and finishing at inlet 4. If your G7/G8 Dock is configured such that your bump test or calibration sequence is different than the flow charts below, your G7/G8 Dock gas inlets should be reconfigured to match the sequence outlined in the gas order flow charts.


Test di funzionamento o calibrazione tramite l'ordine di fornitura del gas Diagrammi di flusso

  1. Indicare i gas che è necessario sottoporre a bump test o a calibrazione.
  2. Verificare quale schema procedurale relativo alla fornitura di gas (bombole monogas o bombole combinate) occorre consultare.
  3. Stabilire l'ordine in cui è necessario testare i gas, confrontando i sensori di gas che si stanno testando con l'ordine indicato nel diagramma di flusso relativo ai gas corrispondente.
    Nota:

    G7/G8 Dock will bump test and calibrate your device in the same order as the gas inlets, starting at inlet 1 and finishing at inlet 4.

  4. Eseguire il bump test o la calibrazione di ciascun gas nell'ordine indicato dal diagramma di flusso.
    Importante:

    Always bump test or calibrate your device using calibration gas concentrations appropriate for your G7 or G8 device configuration. For more information on configuring calibration gas concentrations, refer to the Blackline Live support pages.

Always follow the prompts on your G7 or G8 to ensure that the procedure test times and flow rates are appropriate to the gas you are testing.

Always follow Blackline’s recommendations for configuring your G7/G8 Dock gas inlets. For example, in the case where Cl2 and NH3 sensors are on the same cartridge, connect the Cl2 gas cylinder to inlet 1, and connect NH3 to inlet 2. For more information, refer to the G7 Dock Technical User Manual.

EXO
G7
Cartuccia multigas
Cartuccia monogas
Cartucce

Last updated: October 13, 2026